How To Hang Up A Skateboard

Whether you have a collection of decorative skateboard decks or a excess that you're waiting to skate, hanging your skateboards on the wall is an awesome way to showcase your favorite graphics. There are a number of ways to mount your skateboard to the wall, with or without nails, simply equally someone who's a renter, opting for no-pigsty options is pretty much my merely option. Since I remember we can all concur that the fewer holes in your wall the better, these methods volition provide options that don't require screws or nails where possible.

To start things off, let's go into some more DIY ways to hang a skateboard both vertically or horizontally. After, I'll share a few cool mounting racks to consider if you are looking for skateboard deck storage more than decorative mounting.

1. Vertical Skateboard Wall Mounting

This is the all-time pick if you accept a few decks to mount next. Since skateboard graphics are often oriented vertically, this mounting position offers the all-time view of the artwork.

Before yous get started, here are the tools and materials you'll need:

Scissors or knife
Fishing Line, or Thin Paracord
Agglutinative Command Hooks
15 minutes of your day

The command hooks you choose are upwardly to you. I had some larger ones laying around from another dwelling project, and then that's what I'll be using in my examples. The main thing to consider is the maximum strength the hooks can concur. Skateboard decks by themselves only weigh a few pounds, then an adhesive hook rated for 5lbs or more volition practice the job. Larger decks such as cruisers or longboard decks can counterbalance more than 5lbs, so make sure to double-check the weight of your deck before mounting.

Stride ane: Mountain Your Command Claw

Command hooks come with adhesive strips that easily stick onto the hook and the wall. Be certain to follow the mounting instructions listed by the agglutinative hook yous are using. In near cases, you volition demand to wait 30 – lx minutes before adding weight to the hook.

Step ii: Cut 8 – 12 Inches Of Fishing Line Or Rope

With the control hook mounted where you want your skateboard to hang, cut viii to 12 inches of line-fishing line from the spool, or take the same amount from your paracord or rope. This line will be threaded through the skateboard so the shorter the line, the closer to the claw your deck will mount.

Stride 3: Thread The Line Through The Top Bolt Holes In The Deck

Take each finish of your line and poke it through the upper bolt holes at the top of your graphic. Make sure to start from the graphic side, pushing the line through to the top side of the deck.

Step 4: Necktie The Rope Or Fishing Line Together

With the loose ends pushed through your skateboard, tie them into a knot to create a circled loop. A double fisherman knot is the most solid knot choice to use since it won't come undone. However, a few basic overhand knots can get the job done also if you're not knot savvy.

Footstep v: Loop The Rope Or Line-fishing Line Onto The Command Hook

With the line tied together, place the loop over the hook of the command hook and position your skateboard until it's straight. At present rinse and repeat for the remaining skateboard decks you lot want to mount!

With this wall mounting solution, it's all-time to not accept grip tape on your skateboard as it may crusade impairment to your walls.

2. Horizontal Skateboard Wall Mounting

If you lot have a deck with horizontal graphics, mounting the board to your wall horizontally may exist the amend way to go. Going from a similar technique as the last mounting pick, this method requires some slightly different knot tying to go the chore done.

Hither's what you'll need for this mounting option:

Pair of scissors Or A Pocketknife
Fishing line, Thin Paracord, or Rope
Command Hooks (1 for each skateboard)
Basic Knot Tying Skills
20 Minutes Of Your Day

Once more, be sure y'all are using control hooks rated for at least 5lbs for standard skateboard decks. For larger-width decks or longboards, check the weight of your deck earlier buying a command hook. That way nil comes crashing downwards afterwards you mount!

Step 1: Mount Your Command Hook

One time again, cull a location for your command claw while keeping in heed the length of your skateboard deck. If you program to mountain multiple boards in a row, or stacked vertically on the wall, be sure to measure the general distance before placing the hooks.

Step 2: Get 2 – 3 Feet Of Fishing Line Or Rope

Since you lot need enough rope to become the length of your skateboard deck, this time you lot'll need a little more length. By having a long slice of cord it's easier to adjust the superlative of your skateboard once it's hung. I am using about 3 feet of paracord in this case.

Footstep 3: Thread One Terminate Of Line Diagonally Through The Bolt Holes

Starting from the top of the deck, push the rope through to the other side. Now thread it back through the commodities hole diagonal from where yous started. Ideally, the second bolt hole you go through is on the bottom side of your deck when it's in the mounted position.

Pace 4: Tie An Overhand On A Bite & Thread The Remaining Line Through

With the stop of the rope yous just poked through, have a seize with teeth of rope and tie an overhand knot to create a loop.

Now have the other end of your rope and thread it through the loop you simply created and pull tight. Now, this side of the board is secured.

Footstep 5: Echo Thread Pattern On Other Side

Taking the finish of your rope to the other side of your deck, poke it through the closest bolt hole, then thread diagonally to the bottom bolt hole as shown below.

Footstep 6: Tie A Double Fisherman Around The Center Rope

With the remaining end of your rope, pull it through until you have the desired length for hanging. One time y'all're happy, tie a double fisherman around the rope that's stretching between the 2 ends of the lath.

*Poke Finish Through Loops And Pull Tight*

A double fisherman can slide up or down after it's tied so it's like shooting fish in a barrel to conform the length of the line one time y'all're done. Meanwhile, the friction of the rope going diagonally through the bolt holes is enough to prevent the rope from slipping.

Stride 7: Mount Your Skateboard To The Wall

Now loop the center of the rope over the control claw on the wall. If the rope is too long y'all may come across the command claw to a higher place your board. In that case, simply slide the double fisherman knot up the rope to shorten the rope and go along the skateboard snug to the hook.

iii. Mounting A Skateboard Deck With Wheels To A Wall

If you aren't going for equally much of a decorative look, but more so want a place to hang your skateboards when you aren't using them, you lot can use a piece of rope slung on a wall to easily mount a complete deck. Although this method certainly isn't as artful, information technology gets the job done and is an easy DIY mounting solution when you lot have trucks on your skateboard.

Here's what you'll need for mounting a complete deck:

Pair of scissors Or A Knife
Paracord or Rope
Command Hooks Rated For 10lbs+
Basic Knot Tying Skills
15 Minutes Of Your 24-hour interval

Step 1: Tie An Overhand On A Seize with teeth On Either End Of Your Rope

First, choose a length of rope suited for the mounting area. If you are planning to only mount i skateboard, three feet or rope will be plenty. One time your rope is cut to size, tie an overhand on a bite on either end of your rope.

Step 2: Place Your Command Hooks At The Aforementioned Length As Your Rope

Considering the length of your rope, place the control hooks far enough apart and so your rope is about taught, but even so has a slight bend in information technology. If you are short of wall space, y'all can go on the hooks closer together but at that place will be more sag in the rope, similar in my example.

Footstep 3: Loop Each End Of The Rope Over The Control Hooks

Loop the knots you tied in step one onto the command hooks to stretch the rope between the 2 hooks.

Footstep four: Place The Rope Nether Your Trucks To Mountain The Skateboard

Accept your built skateboard with the wheels facing you, place it behind the rope, then place the rope underneath the trucks and wheels. The rope will cradle your skateboard and keep it secure confronting the wall.

This method is a pretty DIY solution only gets the task done. If you want a more visually pleasing way to mount your skateboards, with or without trucks and wheels, this adjacent department is for you.

4. Using Store-Bought Skateboard Wall Hangers

If DIY isn't your jam, there are a few solid hangers out in that location designed specifically for skateboard decks.

The first option to look at is the skateboard mounting rack from Grass Racks. This rack can mountain ane or multiple skateboards vertically in a similar style to what you see in your local skate shops. The beauty of these racks is they tin can be used to mount regular skateboard decks, or complete skateboards. Merely proceed in mind that you'll demand to drill into the wall to mount this shelving unit deeply.

For mounting skateboard decks without trucks and wheels, you lot'll need the Lana'i Series mount. However, if you are mounting a skateboard with trucks and wheels, you lot need to utilise the Moloka'i Series.

Some other option to get with for hanging skateboards with wheels is a simple wall hook that yous tin detect on Amazon. These hooks loop under your wheels and are a quick and low-profile fashion to mountain a complete skateboard to your wall. The only downside, once again, is that you'll need to drill a hole to mount these hooks properly.

Then whether you want a DIY style to mountain your skateboard to the wall, or a more serious wall mounting unit from Grass Racks or Amazon, at that place are tons of ways to mount your board for any artful!

Happy Hanging!

Brendan 🙂

Source: https://theshredtactic.com/how-to-hang-a-skateboard-on-a-wall/